[ViewVC] Diff of: group/trunk/tengDissertation/Introduction.tex

Comparing trunk/tengDissertation/Introduction.tex (file contents):
Revision 2697 by tim, Fri Apr 7 05:03:54 2006 UTC vs.
Revision 2720 by tim, Wed Apr 19 19:46:53 2006 UTC

+\end{equation}
+A point mass interacting with other bodies moves with the
+acceleration along the direction of the force acting on it. Let
-<
+$F_ij$ be the force that particle $i$ exerts on particle $j$, and
-<
+$F_ji$ be the force that particle $j$ exerts on particle $i$.
->
+$F_{ij}$ be the force that particle $i$ exerts on particle $j$, and
->
+$F_{ji}$ be the force that particle $j$ exerts on particle $i$.
+Newton’s third law states that
+\begin{equation}
-<
+F_ij = -F_ji
->
+F_{ij} = -F_{ji}
+ \label{introEquation:newtonThirdLaw}
+\end{equation}
+\subsubsection{\label{introSection:equationOfMotionLagrangian}The
+Equations of Motion in Lagrangian Mechanics}
-<
+for a holonomic system of $f$ degrees of freedom, the equations of
->
+For a holonomic system of $f$ degrees of freedom, the equations of
+motion in the Lagrangian form is
+\begin{equation}
+\frac{d}{{dt}}\frac{{\partial L}}{{\partial \dot q_i }} -
+}}\dot p_i } \right)}  = \sum\limits_i {\left( {\frac{{\partial
+H}}{{\partial q_i }}\frac{{\partial H}}{{\partial p_i }} -
+\frac{{\partial H}}{{\partial p_i }}\frac{{\partial H}}{{\partial
-<
+q_i }}} \right) = 0}
-<
+\label{introEquation:conserveHalmitonian}
->
+q_i }}} \right) = 0} \label{introEquation:conserveHalmitonian}
+\end{equation}
-–
+When studying Hamiltonian system, it is more convenient to use
-–
+notation
-–
+\begin{equation}
-–
+r = r(q,p)^T
-–
+\end{equation}
-–
+and to introduce a $2n \times 2n$ canonical structure matrix $J$,
-–
+\begin{equation}
-–
+J = \left( {\begin{array}{*{20}c}
-–
+& I  \\
-–
+   { - I} & 0  \\
-–
+\end{array}} \right)
-–
+\label{introEquation:canonicalMatrix}
-–
+\end{equation}
-–
+where $I$ is a $n \times n$ identity matrix and $J$ is a
-–
+skew-symmetric matrix ($ J^T  =  - J $). Thus, Hamiltonian system
-–
+can be rewritten as,
-–
+\begin{equation}
-–
+\frac{d}{{dt}}r = J\nabla _r H(r)
-–
+\label{introEquation:compactHamiltonian}
-–
+\end{equation}
-–
+\section{\label{introSection:statisticalMechanics}Statistical
+Mechanics}
+The thermodynamic behaviors and properties of Molecular Dynamics
+simulation are governed by the principle of Statistical Mechanics.
+The following section will give a brief introduction to some of the
-<
+Statistical Mechanics concepts presented in this dissertation.
->
+Statistical Mechanics concepts and theorem presented in this
->
+dissertation.
-<
+\subsection{\label{introSection:ensemble}Ensemble and Phase Space}
->
+\subsection{\label{introSection:ensemble}Phase Space and Ensemble}
->
->
+Mathematically, phase space is the space which represents all
->
+possible states. Each possible state of the system corresponds to
->
+one unique point in the phase space. For mechanical systems, the
->
+phase space usually consists of all possible values of position and
->
+momentum variables. Consider a dynamic system in a cartesian space,
->
+where each of the $6f$ coordinates and momenta is assigned to one of
->
+$6f$ mutually orthogonal axes, the phase space of this system is a
->
+$6f$ dimensional space. A point, $x = (q_1 , \ldots ,q_f ,p_1 ,
->
+\ldots ,p_f )$, with a unique set of values of $6f$ coordinates and
->
+momenta is a phase space vector.
->
->
+A microscopic state or microstate of a classical system is
->
+specification of the complete phase space vector of a system at any
->
+instant in time. An ensemble is defined as a collection of systems
->
+sharing one or more macroscopic characteristics but each being in a
->
+unique microstate. The complete ensemble is specified by giving all
->
+systems or microstates consistent with the common macroscopic
->
+characteristics of the ensemble. Although the state of each
->
+individual system in the ensemble could be precisely described at
->
+any instance in time by a suitable phase space vector, when using
->
+ensembles for statistical purposes, there is no need to maintain
->
+distinctions between individual systems, since the numbers of
->
+systems at any time in the different states which correspond to
->
+different regions of the phase space are more interesting. Moreover,
->
+in the point of view of statistical mechanics, one would prefer to
->
+use ensembles containing a large enough population of separate
->
+members so that the numbers of systems in such different states can
->
+be regarded as changing continuously as we traverse different
->
+regions of the phase space. The condition of an ensemble at any time
->
+can be regarded as appropriately specified by the density $\rho$
->
+with which representative points are distributed over the phase
->
+space. The density of distribution for an ensemble with $f$ degrees
->
+of freedom is defined as,
->
+\begin{equation}
->
+\rho  = \rho (q_1 , \ldots ,q_f ,p_1 , \ldots ,p_f ,t).
->
+\label{introEquation:densityDistribution}
->
+\end{equation}
->
+Governed by the principles of mechanics, the phase points change
->
+their value which would change the density at any time at phase
->
+space. Hence, the density of distribution is also to be taken as a
->
+function of the time.
->
->
+The number of systems $\delta N$ at time $t$ can be determined by,
->
+\begin{equation}
->
+\delta N = \rho (q,p,t)dq_1  \ldots dq_f dp_1  \ldots dp_f.
->
+\label{introEquation:deltaN}
->
+\end{equation}
->
+Assuming a large enough population of systems are exploited, we can
->
+sufficiently approximate $\delta N$ without introducing
->
+discontinuity when we go from one region in the phase space to
->
+another. By integrating over the whole phase space,
->
+\begin{equation}
->
+N = \int { \ldots \int {\rho (q,p,t)dq_1 } ...dq_f dp_1 } ...dp_f
->
+\label{introEquation:totalNumberSystem}
->
+\end{equation}
->
+gives us an expression for the total number of the systems. Hence,
->
+the probability per unit in the phase space can be obtained by,
->
+\begin{equation}
->
+\frac{{\rho (q,p,t)}}{N} = \frac{{\rho (q,p,t)}}{{\int { \ldots \int
->
+{\rho (q,p,t)dq_1 } ...dq_f dp_1 } ...dp_f }}.
->
+\label{introEquation:unitProbability}
->
+\end{equation}
->
+With the help of Equation(\ref{introEquation:unitProbability}) and
->
+the knowledge of the system, it is possible to calculate the average
->
+value of any desired quantity which depends on the coordinates and
->
+momenta of the system. Even when the dynamics of the real system is
->
+complex, or stochastic, or even discontinuous, the average
->
+properties of the ensemble of possibilities as a whole may still
->
+remain well defined. For a classical system in thermal equilibrium
->
+with its environment, the ensemble average of a mechanical quantity,
->
+$\langle A(q , p) \rangle_t$, takes the form of an integral over the
->
+phase space of the system,
->
+\begin{equation}
->
+\langle  A(q , p) \rangle_t = \frac{{\int { \ldots \int {A(q,p)\rho
->
+(q,p,t)dq_1 } ...dq_f dp_1 } ...dp_f }}{{\int { \ldots \int {\rho
->
+(q,p,t)dq_1 } ...dq_f dp_1 } ...dp_f }}
->
+\label{introEquation:ensembelAverage}
->
+\end{equation}
->
->
+There are several different types of ensembles with different
->
+statistical characteristics. As a function of macroscopic
->
+parameters, such as temperature \textit{etc}, partition function can
->
+be used to describe the statistical properties of a system in
->
+thermodynamic equilibrium.
-+
+As an ensemble of systems, each of which is known to be thermally
-+
+isolated and conserve energy, Microcanonical ensemble(NVE) has a
-+
+partition function like,
-+
+\begin{equation}
-+
+\Omega (N,V,E) = e^{\beta TS} \label{introEquation:NVEPartition}.
-+
+\end{equation}
-+
+A canonical ensemble(NVT)is an ensemble of systems, each of which
-+
+can share its energy with a large heat reservoir. The distribution
-+
+of the total energy amongst the possible dynamical states is given
-+
+by the partition function,
-+
+\begin{equation}
-+
+\Omega (N,V,T) = e^{ - \beta A}
-+
+\label{introEquation:NVTPartition}
-+
+\end{equation}
-+
+Here, $A$ is the Helmholtz free energy which is defined as $ A = U -
-+
+TS$. Since most experiment are carried out under constant pressure
-+
+condition, isothermal-isobaric ensemble(NPT) play a very important
-+
+role in molecular simulation. The isothermal-isobaric ensemble allow
-+
+the system to exchange energy with a heat bath of temperature $T$
-+
+and to change the volume as well. Its partition function is given as
-+
+\begin{equation}
-+
+\Delta (N,P,T) =  - e^{\beta G}.
-+
+ \label{introEquation:NPTPartition}
-+
+\end{equation}
-+
+Here, $G = U - TS + PV$, and $G$ is called Gibbs free energy.
-+
-+
+\subsection{\label{introSection:liouville}Liouville's theorem}
-+
-+
+The Liouville's theorem is the foundation on which statistical
-+
+mechanics rests. It describes the time evolution of phase space
-+
+distribution function. In order to calculate the rate of change of
-+
+$\rho$, we begin from Equation(\ref{introEquation:deltaN}). If we
-+
+consider the two faces perpendicular to the $q_1$ axis, which are
-+
+located at $q_1$ and $q_1 + \delta q_1$, the number of phase points
-+
+leaving the opposite face is given by the expression,
-+
+\begin{equation}
-+
+\left( {\rho  + \frac{{\partial \rho }}{{\partial q_1 }}\delta q_1 }
-+
+\right)\left( {\dot q_1  + \frac{{\partial \dot q_1 }}{{\partial q_1
-+
+}}\delta q_1 } \right)\delta q_2  \ldots \delta q_f \delta p_1
-+
+\ldots \delta p_f .
-+
+\end{equation}
-+
+Summing all over the phase space, we obtain
-+
+\begin{equation}
-+
+\frac{{d(\delta N)}}{{dt}} =  - \sum\limits_{i = 1}^f {\left[ {\rho
-+
+\left( {\frac{{\partial \dot q_i }}{{\partial q_i }} +
-+
+\frac{{\partial \dot p_i }}{{\partial p_i }}} \right) + \left(
-+
+{\frac{{\partial \rho }}{{\partial q_i }}\dot q_i  + \frac{{\partial
-+
+\rho }}{{\partial p_i }}\dot p_i } \right)} \right]} \delta q_1
-+
+\ldots \delta q_f \delta p_1  \ldots \delta p_f .
-+
+\end{equation}
-+
+Differentiating the equations of motion in Hamiltonian formalism
-+
+(\ref{introEquation:motionHamiltonianCoordinate},
-+
+\ref{introEquation:motionHamiltonianMomentum}), we can show,
-+
+\begin{equation}
-+
+\sum\limits_i {\left( {\frac{{\partial \dot q_i }}{{\partial q_i }}
-+
++ \frac{{\partial \dot p_i }}{{\partial p_i }}} \right)}  = 0 ,
-+
+\end{equation}
-+
+which cancels the first terms of the right hand side. Furthermore,
-+
+divining $ \delta q_1  \ldots \delta q_f \delta p_1  \ldots \delta
-+
+p_f $ in both sides, we can write out Liouville's theorem in a
-+
+simple form,
-+
+\begin{equation}
-+
+\frac{{\partial \rho }}{{\partial t}} + \sum\limits_{i = 1}^f
-+
+{\left( {\frac{{\partial \rho }}{{\partial q_i }}\dot q_i  +
-+
+\frac{{\partial \rho }}{{\partial p_i }}\dot p_i } \right)}  = 0 .
-+
+\label{introEquation:liouvilleTheorem}
-+
+\end{equation}
-+
-+
+Liouville's theorem states that the distribution function is
-+
+constant along any trajectory in phase space. In classical
-+
+statistical mechanics, since the number of particles in the system
-+
+is huge, we may be able to believe the system is stationary,
-+
+\begin{equation}
-+
+\frac{{\partial \rho }}{{\partial t}} = 0.
-+
+\label{introEquation:stationary}
-+
+\end{equation}
-+
+In such stationary system, the density of distribution $\rho$ can be
-+
+connected to the Hamiltonian $H$ through Maxwell-Boltzmann
-+
+distribution,
-+
+\begin{equation}
-+
+\rho  \propto e^{ - \beta H}
-+
+\label{introEquation:densityAndHamiltonian}
-+
+\end{equation}
-+
-+
+\subsubsection{\label{introSection:phaseSpaceConservation}Conservation of Phase Space}
-+
+Lets consider a region in the phase space,
-+
+\begin{equation}
-+
+\delta v = \int { \ldots \int {dq_1 } ...dq_f dp_1 } ..dp_f .
-+
+\end{equation}
-+
+If this region is small enough, the density $\rho$ can be regarded
-+
+as uniform over the whole phase space. Thus, the number of phase
-+
+points inside this region is given by,
-+
+\begin{equation}
-+
+\delta N = \rho \delta v = \rho \int { \ldots \int {dq_1 } ...dq_f
-+
+dp_1 } ..dp_f.
-+
+\end{equation}
-+
-+
+\begin{equation}
-+
+\frac{{d(\delta N)}}{{dt}} = \frac{{d\rho }}{{dt}}\delta v + \rho
-+
+\frac{d}{{dt}}(\delta v) = 0.
-+
+\end{equation}
-+
+With the help of stationary assumption
-+
+(\ref{introEquation:stationary}), we obtain the principle of the
-+
+\emph{conservation of extension in phase space},
-+
+\begin{equation}
-+
+\frac{d}{{dt}}(\delta v) = \frac{d}{{dt}}\int { \ldots \int {dq_1 }
-+
+...dq_f dp_1 } ..dp_f  = 0.
-+
+\label{introEquation:volumePreserving}
-+
+\end{equation}
-+
-+
+\subsubsection{\label{introSection:liouvilleInOtherForms}Liouville's Theorem in Other Forms}
-+
-+
+Liouville's theorem can be expresses in a variety of different forms
-+
+which are convenient within different contexts. For any two function
-+
+$F$ and $G$ of the coordinates and momenta of a system, the Poisson
-+
+bracket ${F, G}$ is defined as
-+
+\begin{equation}
-+
+\left\{ {F,G} \right\} = \sum\limits_i {\left( {\frac{{\partial
-+
+F}}{{\partial q_i }}\frac{{\partial G}}{{\partial p_i }} -
-+
+\frac{{\partial F}}{{\partial p_i }}\frac{{\partial G}}{{\partial
-+
+q_i }}} \right)}.
-+
+\label{introEquation:poissonBracket}
-+
+\end{equation}
-+
+Substituting equations of motion in Hamiltonian formalism(
-+
+\ref{introEquation:motionHamiltonianCoordinate} ,
-+
+\ref{introEquation:motionHamiltonianMomentum} ) into
-+
+(\ref{introEquation:liouvilleTheorem}), we can rewrite Liouville's
-+
+theorem using Poisson bracket notion,
-+
+\begin{equation}
-+
+\left( {\frac{{\partial \rho }}{{\partial t}}} \right) =  - \left\{
-+
+{\rho ,H} \right\}.
-+
+\label{introEquation:liouvilleTheromInPoissin}
-+
+\end{equation}
-+
+Moreover, the Liouville operator is defined as
-+
+\begin{equation}
-+
+iL = \sum\limits_{i = 1}^f {\left( {\frac{{\partial H}}{{\partial
-+
+p_i }}\frac{\partial }{{\partial q_i }} - \frac{{\partial
-+
+H}}{{\partial q_i }}\frac{\partial }{{\partial p_i }}} \right)}
-+
+\label{introEquation:liouvilleOperator}
-+
+\end{equation}
-+
+In terms of Liouville operator, Liouville's equation can also be
-+
+expressed as
-+
+\begin{equation}
-+
+\left( {\frac{{\partial \rho }}{{\partial t}}} \right) =  - iL\rho
-+
+\label{introEquation:liouvilleTheoremInOperator}
-+
+\end{equation}
-+
+\subsection{\label{introSection:ergodic}The Ergodic Hypothesis}
+Various thermodynamic properties can be calculated from Molecular
+ensemble average. It states that time average and average over the
+statistical ensemble are identical \cite{Frenkel1996, leach01:mm}.
+\begin{equation}
-<
+\langle A \rangle_t = \mathop {\lim }\limits_{t \to \infty }
-<
+\frac{1}{t}\int\limits_0^t {A(p(t),q(t))dt = \int\limits_\Gamma
-<
+{A(p(t),q(t))} } \rho (p(t), q(t)) dpdq
->
+\langle A(q , p) \rangle_t = \mathop {\lim }\limits_{t \to \infty }
->
+\frac{1}{t}\int\limits_0^t {A(q(t),p(t))dt = \int\limits_\Gamma
->
+{A(q(t),p(t))} } \rho (q(t), p(t)) dqdp
+\end{equation}
-<
+where $\langle A \rangle_t$ is an equilibrium value of a physical
-<
+quantity and $\rho (p(t), q(t))$ is the equilibrium distribution
-<
+function. If an observation is averaged over a sufficiently long
-<
+time (longer than relaxation time), all accessible microstates in
-<
+phase space are assumed to be equally probed, giving a properly
-<
+weighted statistical average. This allows the researcher freedom of
-<
+choice when deciding how best to measure a given observable. In case
-<
+an ensemble averaged approach sounds most reasonable, the Monte
-<
+Carlo techniques\cite{metropolis:1949} can be utilized. Or if the
-<
+system lends itself to a time averaging approach, the Molecular
-<
+Dynamics techniques in Sec.~\ref{introSection:molecularDynamics}
-<
+will be the best choice\cite{Frenkel1996}.
->
+where $\langle  A(q , p) \rangle_t$ is an equilibrium value of a
->
+physical quantity and $\rho (p(t), q(t))$ is the equilibrium
->
+distribution function. If an observation is averaged over a
->
+sufficiently long time (longer than relaxation time), all accessible
->
+microstates in phase space are assumed to be equally probed, giving
->
+a properly weighted statistical average. This allows the researcher
->
+freedom of choice when deciding how best to measure a given
->
+observable. In case an ensemble averaged approach sounds most
->
+reasonable, the Monte Carlo techniques\cite{metropolis:1949} can be
->
+utilized. Or if the system lends itself to a time averaging
->
+approach, the Molecular Dynamics techniques in
->
+Sec.~\ref{introSection:molecularDynamics} will be the best
->
+choice\cite{Frenkel1996}.
+\section{\label{introSection:geometricIntegratos}Geometric Integrators}
+A variety of numerical integrators were proposed to simulate the
+is a \emph{symplectomorphism} if it is a \emph{diffeomorphims} and
+the \emph{pullback} of $\eta$ under f is equal to $\omega$.
+Canonical transformation is an example of symplectomorphism in
-<
+classical mechanics. According to Liouville's theorem, the
-<
+Hamiltonian \emph{flow} or \emph{symplectomorphism} generated by the
-<
+Hamiltonian vector filed preserves the volume form on the phase
-<
+space, which is the basis of classical statistical mechanics.
->
+classical mechanics.
-<
+\subsection{\label{introSection:exactFlow}The Exact Flow of ODE}
->
+\subsection{\label{introSection:ODE}Ordinary Differential Equations}
-<
+\subsection{\label{introSection:hamiltonianSplitting}Hamiltonian Splitting}
->
+For a ordinary differential system defined as
->
+\begin{equation}
->
+\dot x = f(x)
->
+\end{equation}
->
+where $x = x(q,p)^T$, this system is canonical Hamiltonian, if
->
+\begin{equation}
->
+f(r) = J\nabla _x H(r).
->
+\end{equation}
->
+$H = H (q, p)$ is Hamiltonian function and $J$ is the skew-symmetric
->
+matrix
->
+\begin{equation}
->
+J = \left( {\begin{array}{*{20}c}
->
+& I  \\
->
+   { - I} & 0  \\
->
+\end{array}} \right)
->
+\label{introEquation:canonicalMatrix}
->
+\end{equation}
->
+where $I$ is an identity matrix. Using this notation, Hamiltonian
->
+system can be rewritten as,
->
+\begin{equation}
->
+\frac{d}{{dt}}x = J\nabla _x H(x)
->
+\label{introEquation:compactHamiltonian}
->
+\end{equation}In this case, $f$ is
->
+called a \emph{Hamiltonian vector field}.
-<
+\section{\label{introSection:molecularDynamics}Molecular Dynamics}
->
+Another generalization of Hamiltonian dynamics is Poisson Dynamics,
->
+\begin{equation}
->
+\dot x = J(x)\nabla _x H \label{introEquation:poissonHamiltonian}
->
+\end{equation}
->
+The most obvious change being that matrix $J$ now depends on $x$.
-<
+As a special discipline of molecular modeling, Molecular dynamics
-<
+has proven to be a powerful tool for studying the functions of
-<
+biological systems, providing structural, thermodynamic and
-<
+dynamical information.
->
+\subsection{\label{introSection:exactFlow}Exact Flow}
-<
+\subsection{\label{introSec:mdInit}Initialization}
->
+Let $x(t)$ be the exact solution of the ODE system,
->
+\begin{equation}
->
+\frac{{dx}}{{dt}} = f(x) \label{introEquation:ODE}
->
+\end{equation}
->
+The exact flow(solution) $\varphi_\tau$ is defined by
->
+\[
->
+x(t+\tau) =\varphi_\tau(x(t))
->
+\]
->
+where $\tau$ is a fixed time step and $\varphi$ is a map from phase
->
+space to itself. The flow has the continuous group property,
->
+\begin{equation}
->
+\varphi _{\tau _1 }  \circ \varphi _{\tau _2 }  = \varphi _{\tau _1
->
++ \tau _2 } .
->
+\end{equation}
->
+In particular,
->
+\begin{equation}
->
+\varphi _\tau   \circ \varphi _{ - \tau }  = I
->
+\end{equation}
->
+Therefore, the exact flow is self-adjoint,
->
+\begin{equation}
->
+\varphi _\tau   = \varphi _{ - \tau }^{ - 1}.
->
+\end{equation}
->
+The exact flow can also be written in terms of the of an operator,
->
+\begin{equation}
->
+\varphi _\tau  (x) = e^{\tau \sum\limits_i {f_i (x)\frac{\partial
->
+}{{\partial x_i }}} } (x) \equiv \exp (\tau f)(x).
->
+\label{introEquation:exponentialOperator}
->
+\end{equation}
-<
+\subsection{\label{introSection:mdIntegration} Integration of the Equations of Motion}
->
+In most cases, it is not easy to find the exact flow $\varphi_\tau$.
->
+Instead, we use a approximate map, $\psi_\tau$, which is usually
->
+called integrator. The order of an integrator $\psi_\tau$ is $p$, if
->
+the Taylor series of $\psi_\tau$ agree to order $p$,
->
+\begin{equation}
->
+\psi_tau(x) = x + \tau f(x) + O(\tau^{p+1})
->
+\end{equation}
-<
+\section{\label{introSection:rigidBody}Dynamics of Rigid Bodies}
->
+\subsection{\label{introSection:geometricProperties}Geometric Properties}
-<
+A rigid body is a body in which the distance between any two given
-<
+points of a rigid body remains constant regardless of external
-<
+forces exerted on it. A rigid body therefore conserves its shape
-<
+during its motion.
->
+The hidden geometric properties of ODE and its flow play important
->
+roles in numerical studies. Many of them can be found in systems
->
+which occur naturally in applications.
-<
+Applications of dynamics of rigid bodies.
-<
-<
+\subsection{\label{introSection:lieAlgebra}Lie Algebra}
-<
-<
+\subsection{\label{introSection:DLMMotionEquation}The Euler Equations of Rigid Body Motion}
-<
-<
+\subsection{\label{introSection:otherRBMotionEquation}Other Formulations for Rigid Body Motion}
-<
-<
+%\subsection{\label{introSection:poissonBrackets}Poisson Brackets}
-<
-<
+\section{\label{introSection:correlationFunctions}Correlation Functions}
-<
-<
+\section{\label{introSection:langevinDynamics}Langevin Dynamics}
-<
-<
+\subsection{\label{introSection:LDIntroduction}Introduction and application of Langevin Dynamics}
-<
-<
+\subsection{\label{introSection:generalizedLangevinDynamics}Generalized Langevin Dynamics}
-<
->
+Let $\varphi$ be the flow of Hamiltonian vector field, $\varphi$ is
->
+a \emph{symplectic} flow if it satisfies,
+\begin{equation}
-<
+H = \frac{{p^2 }}{{2m}} + U(x) + H_B  + \Delta U(x,x_1 , \ldots x_N)
-<
+\label{introEquation:bathGLE}
->
+{\varphi '}^T J \varphi ' = J.
+\end{equation}
-<
+where $H_B$ is harmonic bath Hamiltonian,
->
+According to Liouville's theorem, the symplectic volume is invariant
->
+under a Hamiltonian flow, which is the basis for classical
->
+statistical mechanics. Furthermore, the flow of a Hamiltonian vector
->
+field on a symplectic manifold can be shown to be a
->
+symplectomorphism. As to the Poisson system,
->
+\begin{equation}
->
+{\varphi '}^T J \varphi ' = J \circ \varphi
->
+\end{equation}
->
+is the property must be preserved by the integrator.
->
->
+It is possible to construct a \emph{volume-preserving} flow for a
->
+source free($ \nabla \cdot f = 0 $) ODE, if the flow satisfies $
->
+\det d\varphi  = 1$. One can show easily that a symplectic flow will
->
+be volume-preserving.
->
->
+Changing the variables $y = h(x)$ in a ODE\ref{introEquation:ODE}
->
+will result in a new system,
+\[
-<
+H_B  =\sum\limits_{\alpha  = 1}^N {\left\{ {\frac{{p_\alpha ^2
-<
+}}{{2m_\alpha  }} + \frac{1}{2}m_\alpha  w_\alpha ^2 } \right\}}
->
+\dot y = \tilde f(y) = ((dh \cdot f)h^{ - 1} )(y).
+\]
-<
+and $\Delta U$ is bilinear system-bath coupling,
->
+The vector filed $f$ has reversing symmetry $h$ if $f = - \tilde f$.
->
+In other words, the flow of this vector field is reversible if and
->
+only if $ h \circ \varphi ^{ - 1}  = \varphi  \circ h $.
->
->
+A \emph{first integral}, or conserved quantity of a general
->
+differential function is a function $ G:R^{2d}  \to R^d $ which is
->
+constant for all solutions of the ODE $\frac{{dx}}{{dt}} = f(x)$ ,
+\[
-<
+\Delta U =  - \sum\limits_{\alpha  = 1}^N {g_\alpha  x_\alpha  x}
->
+\frac{{dG(x(t))}}{{dt}} = 0.
->
+\]
->
+Using chain rule, one may obtain,
->
+\[
->
+\sum\limits_i {\frac{{dG}}{{dx_i }}} f_i (x) = f \bullet \nabla G,
+\]
-<
+Completing the square,
->
+which is the condition for conserving \emph{first integral}. For a
->
+canonical Hamiltonian system, the time evolution of an arbitrary
->
+smooth function $G$ is given by,
->
+\begin{equation}
->
+\begin{array}{c}
->
+ \frac{{dG(x(t))}}{{dt}} = [\nabla _x G(x(t))]^T \dot x(t) \\
->
+  = [\nabla _x G(x(t))]^T J\nabla _x H(x(t)). \\
->
+ \end{array}
->
+\label{introEquation:firstIntegral1}
->
+\end{equation}
->
+Using poisson bracket notion, Equation
->
+\ref{introEquation:firstIntegral1} can be rewritten as
+\[
-<
+H_B  + \Delta U = \sum\limits_{\alpha  = 1}^N {\left\{
-<
+{\frac{{p_\alpha ^2 }}{{2m_\alpha  }} + \frac{1}{2}m_\alpha
-<
+w_\alpha ^2 \left( {x_\alpha   - \frac{{g_\alpha  }}{{m_\alpha
-<
+w_\alpha ^2 }}x} \right)^2 } \right\}}  - \sum\limits_{\alpha  =
-<
+}^N {\frac{{g_\alpha ^2 }}{{2m_\alpha  w_\alpha ^2 }}} x^2
->
+\frac{d}{{dt}}G(x(t)) = \left\{ {G,H} \right\}(x(t)).
+\]
-<
+and putting it back into Eq.~\ref{introEquation:bathGLE},
->
+Therefore, the sufficient condition for $G$ to be the \emph{first
->
+integral} of a Hamiltonian system is
+\[
-<
+H = \frac{{p^2 }}{{2m}} + W(x) + \sum\limits_{\alpha  = 1}^N
-<
+{\left\{ {\frac{{p_\alpha ^2 }}{{2m_\alpha  }} + \frac{1}{2}m_\alpha
-<
+w_\alpha ^2 \left( {x_\alpha   - \frac{{g_\alpha  }}{{m_\alpha
-<
+w_\alpha ^2 }}x} \right)^2 } \right\}}
->
+\left\{ {G,H} \right\} = 0.
+\]
-<
+where
->
+As well known, the Hamiltonian (or energy) H of a Hamiltonian system
->
+is a \emph{first integral}, which is due to the fact $\{ H,H\}  =
->
+$.
->
->
->
+ When designing any numerical methods, one should always try to
->
+preserve the structural properties of the original ODE and its flow.
->
->
+\subsection{\label{introSection:constructionSymplectic}Construction of Symplectic Methods}
->
+A lot of well established and very effective numerical methods have
->
+been successful precisely because of their symplecticities even
->
+though this fact was not recognized when they were first
->
+constructed. The most famous example is leapfrog methods in
->
+molecular dynamics. In general, symplectic integrators can be
->
+constructed using one of four different methods.
->
+\begin{enumerate}
->
+\item Generating functions
->
+\item Variational methods
->
+\item Runge-Kutta methods
->
+\item Splitting methods
->
+\end{enumerate}
->
->
+Generating function tends to lead to methods which are cumbersome
->
+and difficult to use. In dissipative systems, variational methods
->
+can capture the decay of energy accurately. Since their
->
+geometrically unstable nature against non-Hamiltonian perturbations,
->
+ordinary implicit Runge-Kutta methods are not suitable for
->
+Hamiltonian system. Recently, various high-order explicit
->
+Runge--Kutta methods have been developed to overcome this
->
+instability. However, due to computational penalty involved in
->
+implementing the Runge-Kutta methods, they do not attract too much
->
+attention from Molecular Dynamics community. Instead, splitting have
->
+been widely accepted since they exploit natural decompositions of
->
+the system\cite{Tuckerman92}.
->
->
+\subsubsection{\label{introSection:splittingMethod}Splitting Method}
->
->
+The main idea behind splitting methods is to decompose the discrete
->
+$\varphi_h$ as a composition of simpler flows,
->
+\begin{equation}
->
+\varphi _h  = \varphi _{h_1 }  \circ \varphi _{h_2 }  \ldots  \circ
->
+\varphi _{h_n }
->
+\label{introEquation:FlowDecomposition}
->
+\end{equation}
->
+where each of the sub-flow is chosen such that each represent a
->
+simpler integration of the system.
->
->
+Suppose that a Hamiltonian system takes the form,
+\[
-<
+W(x) = U(x) - \sum\limits_{\alpha  = 1}^N {\frac{{g_\alpha ^2
-<
+}}{{2m_\alpha  w_\alpha ^2 }}} x^2
->
+H = H_1 + H_2.
+\]
-<
+Since the first two terms of the new Hamiltonian depend only on the
-<
+system coordinates, we can get the equations of motion for
-<
+Generalized Langevin Dynamics by Hamilton's equations
-<
+\ref{introEquation:motionHamiltonianCoordinate,
-<
+introEquation:motionHamiltonianMomentum},
->
+Here, $H_1$ and $H_2$ may represent different physical processes of
->
+the system. For instance, they may relate to kinetic and potential
->
+energy respectively, which is a natural decomposition of the
->
+problem. If $H_1$ and $H_2$ can be integrated using exact flows
->
+$\varphi_1(t)$ and $\varphi_2(t)$, respectively, a simple first
->
+order is then given by the Lie-Trotter formula
->
+\begin{equation}
->
+\varphi _h  = \varphi _{1,h}  \circ \varphi _{2,h},
->
+\label{introEquation:firstOrderSplitting}
->
+\end{equation}
->
+where $\varphi _h$ is the result of applying the corresponding
->
+continuous $\varphi _i$ over a time $h$. By definition, as
->
+$\varphi_i(t)$ is the exact solution of a Hamiltonian system, it
->
+must follow that each operator $\varphi_i(t)$ is a symplectic map.
->
+It is easy to show that any composition of symplectic flows yields a
->
+symplectic map,
->
+\begin{equation}
->
+(\varphi '\phi ')^T J\varphi '\phi ' = \phi '^T \varphi '^T J\varphi
->
+'\phi ' = \phi '^T J\phi ' = J,
->
+ \label{introEquation:SymplecticFlowComposition}
->
+\end{equation}
->
+where $\phi$ and $\psi$ both are symplectic maps. Thus operator
->
+splitting in this context automatically generates a symplectic map.
->
->
+The Lie-Trotter splitting(\ref{introEquation:firstOrderSplitting})
->
+introduces local errors proportional to $h^2$, while Strang
->
+splitting gives a second-order decomposition,
->
+\begin{equation}
->
+\varphi _h  = \varphi _{1,h/2}  \circ \varphi _{2,h}  \circ \varphi
->
+_{1,h/2} , \label{introEquation:secondOrderSplitting}
->
+\end{equation}
->
+which has a local error proportional to $h^3$. Sprang splitting's
->
+popularity in molecular simulation community attribute to its
->
+symmetric property,
->
+\begin{equation}
->
+\varphi _h^{ - 1} = \varphi _{ - h}.
->
+\label{introEquation:timeReversible}
->
+\end{equation}
->
->
+\subsubsection{\label{introSection:exampleSplittingMethod}Example of Splitting Method}
->
+The classical equation for a system consisting of interacting
->
+particles can be written in Hamiltonian form,
->
+\[
->
+H = T + V
->
+\]
->
+where $T$ is the kinetic energy and $V$ is the potential energy.
->
+Setting $H_1 = T, H_2 = V$ and applying Strang splitting, one
->
+obtains the following:
+\begin{align}
-<
+\dot p &=  - \frac{{\partial H}}{{\partial x}}
-<
+       &= m\ddot x
-<
+       &= - \frac{{\partial W(x)}}{{\partial x}} - \sum\limits_{\alpha  = 1}^N {g_\alpha  \left( {x_\alpha   - \frac{{g_\alpha  }}{{m_\alpha  w_\alpha ^2 }}x} \right)}
-<
+\label{introEq:Lp5}
->
+q(\Delta t) &= q(0) + \dot{q}(0)\Delta t +
->
+    \frac{F[q(0)]}{m}\frac{\Delta t^2}{2}, %
->
+\label{introEquation:Lp10a} \\%
->
+%
->
+\dot{q}(\Delta t) &= \dot{q}(0) + \frac{\Delta t}{2m}
->
+    \biggl [F[q(0)] + F[q(\Delta t)] \biggr]. %
->
+\label{introEquation:Lp10b}
+\end{align}
-<
+, and
->
+where $F(t)$ is the force at time $t$. This integration scheme is
->
+known as \emph{velocity verlet} which is
->
+symplectic(\ref{introEquation:SymplecticFlowComposition}),
->
+time-reversible(\ref{introEquation:timeReversible}) and
->
+volume-preserving (\ref{introEquation:volumePreserving}). These
->
+geometric properties attribute to its long-time stability and its
->
+popularity in the community. However, the most commonly used
->
+velocity verlet integration scheme is written as below,
+\begin{align}
-<
+\dot p_\alpha   &=  - \frac{{\partial H}}{{\partial x_\alpha  }}
-<
+                &= m\ddot x_\alpha
-<
+                &= \- m_\alpha  w_\alpha ^2 \left( {x_\alpha   - \frac{{g_\alpha}}{{m_\alpha  w_\alpha ^2 }}x} \right)
->
+\dot{q}\biggl (\frac{\Delta t}{2}\biggr ) &=
->
+    \dot{q}(0) + \frac{\Delta t}{2m}\, F[q(0)], \label{introEquation:Lp9a}\\%
->
+%
->
+q(\Delta t) &= q(0) + \Delta t\, \dot{q}\biggl (\frac{\Delta t}{2}\biggr ),%
->
+    \label{introEquation:Lp9b}\\%
->
+%
->
+\dot{q}(\Delta t) &= \dot{q}\biggl (\frac{\Delta t}{2}\biggr ) +
->
+    \frac{\Delta t}{2m}\, F[q(0)]. \label{introEquation:Lp9c}
+\end{align}
-+
+From the preceding splitting, one can see that the integration of
-+
+the equations of motion would follow:
-+
+\begin{enumerate}
-+
+\item calculate the velocities at the half step, $\frac{\Delta t}{2}$, from the forces calculated at the initial position.
-<
+\subsection{\label{introSection:laplaceTransform}The Laplace Transform}
->
+\item Use the half step velocities to move positions one whole step, $\Delta t$.
-<
+\[
-<
+L(x) = \int_0^\infty  {x(t)e^{ - pt} dt}
-<
+\]
->
+\item Evaluate the forces at the new positions, $\mathbf{r}(\Delta t)$, and use the new forces to complete the velocity move.
-<
+\[
-<
+L(x + y) = L(x) + L(y)
-<
+\]
->
+\item Repeat from step 1 with the new position, velocities, and forces assuming the roles of the initial values.
->
+\end{enumerate}
-+
+Simply switching the order of splitting and composing, a new
-+
+integrator, the \emph{position verlet} integrator, can be generated,
-+
+\begin{align}
-+
+\dot q(\Delta t) &= \dot q(0) + \Delta tF(q(0))\left[ {q(0) +
-+
+\frac{{\Delta t}}{{2m}}\dot q(0)} \right], %
-+
+\label{introEquation:positionVerlet1} \\%
-+
+%
-+
+q(\Delta t) &= q(0) + \frac{{\Delta t}}{2}\left[ {\dot q(0) + \dot
-+
+q(\Delta t)} \right]. %
-+
+ \label{introEquation:positionVerlet2}
-+
+\end{align}
-+
-+
+\subsubsection{\label{introSection:errorAnalysis}Error Analysis and Higher Order Methods}
-+
-+
+Baker-Campbell-Hausdorff formula can be used to determine the local
-+
+error of splitting method in terms of commutator of the
-+
+operators(\ref{introEquation:exponentialOperator}) associated with
-+
+the sub-flow. For operators $hX$ and $hY$ which are associate to
-+
+$\varphi_1(t)$ and $\varphi_2(t$ respectively , we have
-+
+\begin{equation}
-+
+\exp (hX + hY) = \exp (hZ)
-+
+\end{equation}
-+
+where
-+
+\begin{equation}
-+
+hZ = hX + hY + \frac{{h^2 }}{2}[X,Y] + \frac{{h^3 }}{2}\left(
-+
+{[X,[X,Y]] + [Y,[Y,X]]} \right) +  \ldots .
-+
+\end{equation}
-+
+Here, $[X,Y]$ is the commutators of operator $X$ and $Y$ given by
+\[
-<
+L(ax) = aL(x)
->
+[X,Y] = XY - YX .
+\]
-<
->
+Applying Baker-Campbell-Hausdorff formula to Sprang splitting, we
->
+can obtain
->
+\begin{eqnarray*}
->
+\exp (h X/2)\exp (h Y)\exp (h X/2) & = & \exp (h X + h Y + h^2
->
+[X,Y]/4 + h^2 [Y,X]/4 \\ & & \mbox{} + h^2 [X,X]/8 + h^2 [Y,Y]/8 \\
->
+& & \mbox{} + h^3 [Y,[Y,X]]/12 - h^3 [X,[X,Y]]/24 & & \mbox{} +
->
+\ldots )
->
+\end{eqnarray*}
->
+Since \[ [X,Y] + [Y,X] = 0\] and \[ [X,X] = 0\], the dominant local
->
+error of Spring splitting is proportional to $h^3$. The same
->
+procedure can be applied to general splitting,  of the form
->
+\begin{equation}
->
+\varphi _{b_m h}^2  \circ \varphi _{a_m h}^1  \circ \varphi _{b_{m -
->
+} h}^2  \circ  \ldots  \circ \varphi _{a_1 h}^1 .
->
+\end{equation}
->
+Careful choice of coefficient $a_1 ,\ldot , b_m$ will lead to higher
->
+order method. Yoshida proposed an elegant way to compose higher
->
+order methods based on symmetric splitting. Given a symmetric second
->
+order base method $ \varphi _h^{(2)} $, a fourth-order symmetric
->
+method can be constructed by composing,
+\[
-<
+L(\dot x) = pL(x) - px(0)
->
+\varphi _h^{(4)}  = \varphi _{\alpha h}^{(2)}  \circ \varphi _{\beta
->
+h}^{(2)}  \circ \varphi _{\alpha h}^{(2)}
+\]
-<
->
+where $ \alpha  =  - \frac{{2^{1/3} }}{{2 - 2^{1/3} }}$ and $ \beta
->
+= \frac{{2^{1/3} }}{{2 - 2^{1/3} }}$. Moreover, a symmetric
->
+integrator $ \varphi _h^{(2n + 2)}$ can be composed by
->
+\begin{equation}
->
+\varphi _h^{(2n + 2)}  = \varphi _{\alpha h}^{(2n)}  \circ \varphi
->
+_{\beta h}^{(2n)}  \circ \varphi _{\alpha h}^{(2n)}
->
+\end{equation}
->
+, if the weights are chosen as
+\[
-<
+L(\ddot x) = p^2 L(x) - px(0) - \dot x(0)
->
+\alpha  =  - \frac{{2^{1/(2n + 1)} }}{{2 - 2^{1/(2n + 1)} }},\beta =
->
+\frac{{2^{1/(2n + 1)} }}{{2 - 2^{1/(2n + 1)} }} .
+\]
-+
+\section{\label{introSection:molecularDynamics}Molecular Dynamics}
-+
-+
+As one of the principal tools of molecular modeling, Molecular
-+
+dynamics has proven to be a powerful tool for studying the functions
-+
+of biological systems, providing structural, thermodynamic and
-+
+dynamical information. The basic idea of molecular dynamics is that
-+
+macroscopic properties are related to microscopic behavior and
-+
+microscopic behavior can be calculated from the trajectories in
-+
+simulations. For instance, instantaneous temperature of an
-+
+Hamiltonian system of $N$ particle can be measured by
+\[
-<
+L\left( {\int_0^t {g(t - \tau )h(\tau )d\tau } } \right) = G(p)H(p)
->
+T(t) = \sum\limits_{i = 1}^N {\frac{{m_i v_i^2 }}{{fk_B }}}
+\]
-+
+where $m_i$ and $v_i$ are the mass and velocity of $i$th particle
-+
+respectively, $f$ is the number of degrees of freedom, and $k_B$ is
-+
+the boltzman constant.
-<
+Some relatively important transformation,
-<
+\[
-<
+L(\cos at) = \frac{p}{{p^2  + a^2 }}
->
+A typical molecular dynamics run consists of three essential steps:
->
+\begin{enumerate}
->
+  \item Initialization
->
+    \begin{enumerate}
->
+    \item Preliminary preparation
->
+    \item Minimization
->
+    \item Heating
->
+    \item Equilibration
->
+    \end{enumerate}
->
+  \item Production
->
+  \item Analysis
->
+\end{enumerate}
->
+These three individual steps will be covered in the following
->
+sections. Sec.~\ref{introSec:initialSystemSettings} deals with the
->
+initialization of a simulation. Sec.~\ref{introSec:production} will
->
+discusses issues in production run, including the force evaluation
->
+and the numerical integration schemes of the equations of motion .
->
+Sec.~\ref{introSection:Analysis} provides the theoretical tools for
->
+trajectory analysis.
->
->
+\subsection{\label{introSec:initialSystemSettings}Initialization}
->
->
+\subsubsection{Preliminary preparation}
->
->
+When selecting the starting structure of a molecule for molecular
->
+simulation, one may retrieve its Cartesian coordinates from public
->
+databases, such as RCSB Protein Data Bank \textit{etc}. Although
->
+thousands of crystal structures of molecules are discovered every
->
+year, many more remain unknown due to the difficulties of
->
+purification and crystallization. Even for the molecule with known
->
+structure, some important information is missing. For example, the
->
+missing hydrogen atom which acts as donor in hydrogen bonding must
->
+be added. Moreover, in order to include electrostatic interaction,
->
+one may need to specify the partial charges for individual atoms.
->
+Under some circumstances, we may even need to prepare the system in
->
+a special setup. For instance, when studying transport phenomenon in
->
+membrane system, we may prepare the lipids in bilayer structure
->
+instead of placing lipids randomly in solvent, since we are not
->
+interested in self-aggregation and it takes a long time to happen.
->
->
+\subsubsection{Minimization}
->
->
+It is quite possible that some of molecules in the system from
->
+preliminary preparation may be overlapped with each other. This
->
+close proximity leads to high potential energy which consequently
->
+jeopardizes any molecular dynamics simulations. To remove these
->
+steric overlaps, one typically performs energy minimization to find
->
+a more reasonable conformation. Several energy minimization methods
->
+have been developed to exploit the energy surface and to locate the
->
+local minimum. While converging slowly near the minimum, steepest
->
+descent method is extremely robust when systems are far from
->
+harmonic. Thus, it is often used to refine structure from
->
+crystallographic data. Relied on the gradient or hessian, advanced
->
+methods like conjugate gradient and Newton-Raphson converge rapidly
->
+to a local minimum, while become unstable if the energy surface is
->
+far from quadratic. Another factor must be taken into account, when
->
+choosing energy minimization method, is the size of the system.
->
+Steepest descent and conjugate gradient can deal with models of any
->
+size. Because of the limit of computation power to calculate hessian
->
+matrix and insufficient storage capacity to store them, most
->
+Newton-Raphson methods can not be used with very large models.
->
->
+\subsubsection{Heating}
->
->
+Typically, Heating is performed by assigning random velocities
->
+according to a Gaussian distribution for a temperature. Beginning at
->
+a lower temperature and gradually increasing the temperature by
->
+assigning greater random velocities, we end up with setting the
->
+temperature of the system to a final temperature at which the
->
+simulation will be conducted. In heating phase, we should also keep
->
+the system from drifting or rotating as a whole. Equivalently, the
->
+net linear momentum and angular momentum of the system should be
->
+shifted to zero.
->
->
+\subsubsection{Equilibration}
->
->
+The purpose of equilibration is to allow the system to evolve
->
+spontaneously for a period of time and reach equilibrium. The
->
+procedure is continued until various statistical properties, such as
->
+temperature, pressure, energy, volume and other structural
->
+properties \textit{etc}, become independent of time. Strictly
->
+speaking, minimization and heating are not necessary, provided the
->
+equilibration process is long enough. However, these steps can serve
->
+as a means to arrive at an equilibrated structure in an effective
->
+way.
->
->
+\subsection{\label{introSection:production}Production}
->
->
+\subsubsection{\label{introSec:forceCalculation}The Force Calculation}
->
->
+\subsubsection{\label{introSection:integrationSchemes} Integration
->
+Schemes}
->
->
+\subsection{\label{introSection:Analysis} Analysis}
->
->
+\section{\label{introSection:rigidBody}Dynamics of Rigid Bodies}
->
->
+Rigid bodies are frequently involved in the modeling of different
->
+areas, from engineering, physics, to chemistry. For example,
->
+missiles and vehicle are usually modeled by rigid bodies.  The
->
+movement of the objects in 3D gaming engine or other physics
->
+simulator is governed by the rigid body dynamics. In molecular
->
+simulation, rigid body is used to simplify the model in
->
+protein-protein docking study{\cite{Gray03}}.
->
->
+It is very important to develop stable and efficient methods to
->
+integrate the equations of motion of orientational degrees of
->
+freedom. Euler angles are the nature choice to describe the
->
+rotational degrees of freedom. However, due to its singularity, the
->
+numerical integration of corresponding equations of motion is very
->
+inefficient and inaccurate. Although an alternative integrator using
->
+different sets of Euler angles can overcome this difficulty\cite{},
->
+the computational penalty and the lost of angular momentum
->
+conservation still remain. A singularity free representation
->
+utilizing quaternions was developed by Evans in 1977. Unfortunately,
->
+this approach suffer from the nonseparable Hamiltonian resulted from
->
+quaternion representation, which prevents the symplectic algorithm
->
+to be utilized. Another different approach is to apply holonomic
->
+constraints to the atoms belonging to the rigid body. Each atom
->
+moves independently under the normal forces deriving from potential
->
+energy and constraint forces which are used to guarantee the
->
+rigidness. However, due to their iterative nature, SHAKE and Rattle
->
+algorithm converge very slowly when the number of constraint
->
+increases.
->
->
+The break through in geometric literature suggests that, in order to
->
+develop a long-term integration scheme, one should preserve the
->
+symplectic structure of the flow. Introducing conjugate momentum to
->
+rotation matrix $Q$ and re-formulating Hamiltonian's equation, a
->
+symplectic integrator, RSHAKE, was proposed to evolve the
->
+Hamiltonian system in a constraint manifold by iteratively
->
+satisfying the orthogonality constraint $Q_T Q = 1$. An alternative
->
+method using quaternion representation was developed by Omelyan.
->
+However, both of these methods are iterative and inefficient. In
->
+this section, we will present a symplectic Lie-Poisson integrator
->
+for rigid body developed by Dullweber and his
->
+coworkers\cite{Dullweber1997} in depth.
->
->
+\subsection{\label{introSection:constrainedHamiltonianRB}Constrained Hamiltonian for Rigid Body}
->
+The motion of the rigid body is Hamiltonian with the Hamiltonian
->
+function
->
+\begin{equation}
->
+H = \frac{1}{2}(p^T m^{ - 1} p) + \frac{1}{2}tr(PJ^{ - 1} P) +
->
+V(q,Q) + \frac{1}{2}tr[(QQ^T  - 1)\Lambda ].
->
+\label{introEquation:RBHamiltonian}
->
+\end{equation}
->
+Here, $q$ and $Q$  are the position and rotation matrix for the
->
+rigid-body, $p$ and $P$  are conjugate momenta to $q$  and $Q$ , and
->
+$J$, a diagonal matrix, is defined by
->
+\[
->
+I_{ii}^{ - 1}  = \frac{1}{2}\sum\limits_{i \ne j} {J_{jj}^{ - 1} }
+\]
-+
+where $I_{ii}$ is the diagonal element of the inertia tensor. This
-+
+constrained Hamiltonian equation subjects to a holonomic constraint,
-+
+\begin{equation}
-+
+Q^T Q = 1$, \label{introEquation:orthogonalConstraint}
-+
+\end{equation}
-+
+which is used to ensure rotation matrix's orthogonality.
-+
+Differentiating \ref{introEquation:orthogonalConstraint} and using
-+
+Equation \ref{introEquation:RBMotionMomentum}, one may obtain,
-+
+\begin{equation}
-+
+Q^T PJ^{ - 1}  + J^{ - 1} P^T Q = 0 . \\
-+
+\label{introEquation:RBFirstOrderConstraint}
-+
+\end{equation}
-+
+Using Equation (\ref{introEquation:motionHamiltonianCoordinate},
-+
+\ref{introEquation:motionHamiltonianMomentum}), one can write down
-+
+the equations of motion,
+\[
-<
+L(\sin at) = \frac{a}{{p^2  + a^2 }}
->
+\begin{array}{c}
->
+ \frac{{dq}}{{dt}} = \frac{p}{m} \label{introEquation:RBMotionPosition}\\
->
+ \frac{{dp}}{{dt}} =  - \nabla _q V(q,Q) \label{introEquation:RBMotionMomentum}\\
->
+ \frac{{dQ}}{{dt}} = PJ^{ - 1}  \label{introEquation:RBMotionRotation}\\
->
+ \frac{{dP}}{{dt}} =  - \nabla _Q V(q,Q) - 2Q\Lambda . \label{introEquation:RBMotionP}\\
->
+ \end{array}
+\]
-+
+In general, there are two ways to satisfy the holonomic constraints.
-+
+We can use constraint force provided by lagrange multiplier on the
-+
+normal manifold to keep the motion on constraint space. Or we can
-+
+simply evolve the system in constraint manifold. The two method are
-+
+proved to be equivalent. The holonomic constraint and equations of
-+
+motions define a constraint manifold for rigid body
+\[
-<
+L(1) = \frac{1}{p}
->
+M = \left\{ {(Q,P):Q^T Q = 1,Q^T PJ^{ - 1}  + J^{ - 1} P^T Q = 0}
->
+\right\}.
+\]
-<
+First, the bath coordinates,
->
+Unfortunately, this constraint manifold is not the cotangent bundle
->
+$T_{\star}SO(3)$. However, it turns out that under symplectic
->
+transformation, the cotangent space and the phase space are
->
+diffeomorphic. Introducing
+\[
-<
+p^2 L(x_\alpha  ) - px_\alpha  (0) - \dot x_\alpha  (0) =  - \omega
-<
+_\alpha ^2 L(x_\alpha  ) + \frac{{g_\alpha  }}{{\omega _\alpha
-<
+}}L(x)
->
+\tilde Q = Q,\tilde P = \frac{1}{2}\left( {P - QP^T Q} \right),
+\]
-+
+the mechanical system subject to a holonomic constraint manifold $M$
-+
+can be re-formulated as a Hamiltonian system on the cotangent space
+\[
-<
+L(x_\alpha  ) = \frac{{\frac{{g_\alpha  }}{{\omega _\alpha  }}L(x) +
-<
+px_\alpha  (0) + \dot x_\alpha  (0)}}{{p^2  + \omega _\alpha ^2 }}
->
+T^* SO(3) = \left\{ {(\tilde Q,\tilde P):\tilde Q^T \tilde Q =
->
+,\tilde Q^T \tilde PJ^{ - 1}  + J^{ - 1} P^T \tilde Q = 0} \right\}
+\]
-–
+Then, the system coordinates,
-–
+\begin{align}
-–
+mL(\ddot x) &=  - \frac{1}{p}\frac{{\partial W(x)}}{{\partial x}} -
-–
+\sum\limits_{\alpha  = 1}^N {\left\{ {\frac{{\frac{{g_\alpha
-–
+}}{{\omega _\alpha  }}L(x) + px_\alpha  (0) + \dot x_\alpha
-–
+(0)}}{{p^2  + \omega _\alpha ^2 }} - \frac{{g_\alpha ^2 }}{{m_\alpha
-–
+}}\omega _\alpha ^2 L(x)} \right\}}
-–
+%
-–
+ &= - \frac{1}{p}\frac{{\partial W(x)}}{{\partial x}} -
-–
+ \sum\limits_{\alpha  = 1}^N {\left\{ { - \frac{{g_\alpha ^2 }}{{m_\alpha  \omega _\alpha ^2 }}\frac{p}{{p^2  + \omega _\alpha ^2 }}pL(x)
-–
+ - \frac{p}{{p^2  + \omega _\alpha ^2 }}g_\alpha  x_\alpha  (0)
-–
+ - \frac{1}{{p^2  + \omega _\alpha ^2 }}g_\alpha  \dot x_\alpha  (0)} \right\}}
-–
+\end{align}
-–
+Then, the inverse transform,
-+
+For a body fixed vector $X_i$ with respect to the center of mass of
-+
+the rigid body, its corresponding lab fixed vector $X_0^{lab}$  is
-+
+given as
-+
+\begin{equation}
-+
+X_i^{lab} = Q X_i + q.
-+
+\end{equation}
-+
+Therefore, potential energy $V(q,Q)$ is defined by
-+
+\[
-+
+V(q,Q) = V(Q X_0 + q).
-+
+\]
-+
+Hence, the force and torque are given by
-+
+\[
-+
+\nabla _q V(q,Q) = F(q,Q) = \sum\limits_i {F_i (q,Q)},
-+
+\]
-+
+and
-+
+\[
-+
+\nabla _Q V(q,Q) = F(q,Q)X_i^t
-+
+\]
-+
+respectively.
-+
-+
+As a common choice to describe the rotation dynamics of the rigid
-+
+body, angular momentum on body frame $\Pi  = Q^t P$ is introduced to
-+
+rewrite the equations of motion,
-+
+\begin{equation}
-+
+ \begin{array}{l}
-+
+ \mathop \Pi \limits^ \bullet   = J^{ - 1} \Pi ^T \Pi  + Q^T \sum\limits_i {F_i (q,Q)X_i^T }  - \Lambda  \\
-+
+ \mathop Q\limits^{{\rm{   }} \bullet }  = Q\Pi {\rm{ }}J^{ - 1}  \\
-+
+ \end{array}
-+
+ \label{introEqaution:RBMotionPI}
-+
+\end{equation}
-+
+, as well as holonomic constraints,
-+
+\[
-+
+\begin{array}{l}
-+
+ \Pi J^{ - 1}  + J^{ - 1} \Pi ^t  = 0 \\
-+
+ Q^T Q = 1 \\
-+
+ \end{array}
-+
+\]
-+
-+
+For a vector $v(v_1 ,v_2 ,v_3 ) \in R^3$ and a matrix $\hat v \in
-+
+so(3)^ \star$, the hat-map isomorphism,
-+
+\begin{equation}
-+
+v(v_1 ,v_2 ,v_3 ) \Leftrightarrow \hat v = \left(
-+
+{\begin{array}{*{20}c}
-+
+& { - v_3 } & {v_2 }  \\
-+
+   {v_3 } & 0 & { - v_1 }  \\
-+
+   { - v_2 } & {v_1 } & 0  \\
-+
+\end{array}} \right),
-+
+\label{introEquation:hatmapIsomorphism}
-+
+\end{equation}
-+
+will let us associate the matrix products with traditional vector
-+
+operations
-+
+\[
-+
+\hat vu = v \times u
-+
+\]
-+
-+
+Using \ref{introEqaution:RBMotionPI}, one can construct a skew
-+
+matrix,
-+
+\begin{equation}
-+
+(\mathop \Pi \limits^ \bullet   - \mathop \Pi \limits^ \bullet  ^T
-+
+){\rm{ }} = {\rm{ }}(\Pi  - \Pi ^T ){\rm{ }}(J^{ - 1} \Pi  + \Pi J^{
-+
+- 1} ) + \sum\limits_i {[Q^T F_i (r,Q)X_i^T  - X_i F_i (r,Q)^T Q]} -
-+
+(\Lambda  - \Lambda ^T ) . \label{introEquation:skewMatrixPI}
-+
+\end{equation}
-+
+Since $\Lambda$ is symmetric, the last term of Equation
-+
+\ref{introEquation:skewMatrixPI} is zero, which implies the Lagrange
-+
+multiplier $\Lambda$ is absent from the equations of motion. This
-+
+unique property eliminate the requirement of iterations which can
-+
+not be avoided in other methods\cite{}.
-+
-+
+Applying hat-map isomorphism, we obtain the equation of motion for
-+
+angular momentum on body frame
-+
+\begin{equation}
-+
+\dot \pi  = \pi  \times I^{ - 1} \pi  + \sum\limits_i {\left( {Q^T
-+
+F_i (r,Q)} \right) \times X_i }.
-+
+\label{introEquation:bodyAngularMotion}
-+
+\end{equation}
-+
+In the same manner, the equation of motion for rotation matrix is
-+
+given by
-+
+\[
-+
+\dot Q = Qskew(I^{ - 1} \pi )
-+
+\]
-+
-+
+\subsection{\label{introSection:SymplecticFreeRB}Symplectic
-+
+Lie-Poisson Integrator for Free Rigid Body}
-+
-+
+If there is not external forces exerted on the rigid body, the only
-+
+contribution to the rotational is from the kinetic potential (the
-+
+first term of \ref{ introEquation:bodyAngularMotion}). The free
-+
+rigid body is an example of Lie-Poisson system with Hamiltonian
-+
+function
-+
+\begin{equation}
-+
+T^r (\pi ) = T_1 ^r (\pi _1 ) + T_2^r (\pi _2 ) + T_3^r (\pi _3 )
-+
+\label{introEquation:rotationalKineticRB}
-+
+\end{equation}
-+
+where $T_i^r (\pi _i ) = \frac{{\pi _i ^2 }}{{2I_i }}$ and
-+
+Lie-Poisson structure matrix,
-+
+\begin{equation}
-+
+J(\pi ) = \left( {\begin{array}{*{20}c}
-+
+& {\pi _3 } & { - \pi _2 }  \\
-+
+   { - \pi _3 } & 0 & {\pi _1 }  \\
-+
+   {\pi _2 } & { - \pi _1 } & 0  \\
-+
+\end{array}} \right)
-+
+\end{equation}
-+
+Thus, the dynamics of free rigid body is governed by
-+
+\begin{equation}
-+
+\frac{d}{{dt}}\pi  = J(\pi )\nabla _\pi  T^r (\pi )
-+
+\end{equation}
-+
-+
+One may notice that each $T_i^r$ in Equation
-+
+\ref{introEquation:rotationalKineticRB} can be solved exactly. For
-+
+instance, the equations of motion due to $T_1^r$ are given by
-+
+\begin{equation}
-+
+\frac{d}{{dt}}\pi  = R_1 \pi ,\frac{d}{{dt}}Q = QR_1
-+
+\label{introEqaution:RBMotionSingleTerm}
-+
+\end{equation}
-+
+where
-+
+\[ R_1  = \left( {\begin{array}{*{20}c}
-+
+& 0 & 0  \\
-+
+& 0 & {\pi _1 }  \\
-+
+& { - \pi _1 } & 0  \\
-+
+\end{array}} \right).
-+
+\]
-+
+The solutions of Equation \ref{introEqaution:RBMotionSingleTerm} is
-+
+\[
-+
+\pi (\Delta t) = e^{\Delta tR_1 } \pi (0),Q(\Delta t) =
-+
+Q(0)e^{\Delta tR_1 }
-+
+\]
-+
+with
-+
+\[
-+
+e^{\Delta tR_1 }  = \left( {\begin{array}{*{20}c}
-+
+& 0 & 0  \\
-+
+& {\cos \theta _1 } & {\sin \theta _1 }  \\
-+
+& { - \sin \theta _1 } & {\cos \theta _1 }  \\
-+
+\end{array}} \right),\theta _1  = \frac{{\pi _1 }}{{I_1 }}\Delta t.
-+
+\]
-+
+To reduce the cost of computing expensive functions in $e^{\Delta
-+
+tR_1 }$, we can use Cayley transformation,
-+
+\[
-+
+e^{\Delta tR_1 }  \approx (1 - \Delta tR_1 )^{ - 1} (1 + \Delta tR_1
-+
+)
-+
+\]
-+
+The flow maps for $T_2^r$ and $T_3^r$ can be found in the same
-+
+manner.
-+
-+
+In order to construct a second-order symplectic method, we split the
-+
+angular kinetic Hamiltonian function can into five terms
-+
+\[
-+
+T^r (\pi ) = \frac{1}{2}T_1 ^r (\pi _1 ) + \frac{1}{2}T_2^r (\pi _2
-+
+) + T_3^r (\pi _3 ) + \frac{1}{2}T_2^r (\pi _2 ) + \frac{1}{2}T_1 ^r
-+
+(\pi _1 )
-+
+\].
-+
+Concatenating flows corresponding to these five terms, we can obtain
-+
+an symplectic integrator,
-+
+\[
-+
+\varphi _{\Delta t,T^r }  = \varphi _{\Delta t/2,\pi _1 }  \circ
-+
+\varphi _{\Delta t/2,\pi _2 }  \circ \varphi _{\Delta t,\pi _3 }
-+
+\circ \varphi _{\Delta t/2,\pi _2 }  \circ \varphi _{\Delta t/2,\pi
-+
+_1 }.
-+
+\]
-+
-+
+The non-canonical Lie-Poisson bracket ${F, G}$ of two function
-+
+$F(\pi )$ and $G(\pi )$ is defined by
-+
+\[
-+
+\{ F,G\} (\pi ) = [\nabla _\pi  F(\pi )]^T J(\pi )\nabla _\pi  G(\pi
-+
+)
-+
+\]
-+
+If the Poisson bracket of a function $F$ with an arbitrary smooth
-+
+function $G$ is zero, $F$ is a \emph{Casimir}, which is the
-+
+conserved quantity in Poisson system. We can easily verify that the
-+
+norm of the angular momentum, $\parallel \pi
-+
+\parallel$, is a \emph{Casimir}. Let$ F(\pi ) = S(\frac{{\parallel
-+
+\pi \parallel ^2 }}{2})$ for an arbitrary function $ S:R \to R$ ,
-+
+then by the chain rule
-+
+\[
-+
+\nabla _\pi  F(\pi ) = S'(\frac{{\parallel \pi \parallel ^2
-+
+}}{2})\pi
-+
+\]
-+
+Thus $ [\nabla _\pi  F(\pi )]^T J(\pi ) =  - S'(\frac{{\parallel \pi
-+
+\parallel ^2 }}{2})\pi  \times \pi  = 0 $. This explicit
-+
+Lie-Poisson integrator is found to be extremely efficient and stable
-+
+which can be explained by the fact the small angle approximation is
-+
+used and the norm of the angular momentum is conserved.
-+
-+
+\subsection{\label{introSection:RBHamiltonianSplitting} Hamiltonian
-+
+Splitting for Rigid Body}
-+
-+
+The Hamiltonian of rigid body can be separated in terms of kinetic
-+
+energy and potential energy,
-+
+\[
-+
+H = T(p,\pi ) + V(q,Q)
-+
+\]
-+
+The equations of motion corresponding to potential energy and
-+
+kinetic energy are listed in the below table,
-+
+\begin{center}
-+
+\begin{tabular}{|l|l|}
-+
+  \hline
-+
+  % after \\: \hline or \cline{col1-col2} \cline{col3-col4} ...
-+
+  Potential & Kinetic \\
-+
+  $\frac{{dq}}{{dt}} = \frac{p}{m}$ & $\frac{d}{{dt}}q = p$ \\
-+
+  $\frac{d}{{dt}}p =  - \frac{{\partial V}}{{\partial q}}$ & $ \frac{d}{{dt}}p = 0$ \\
-+
+  $\frac{d}{{dt}}Q = 0$ & $ \frac{d}{{dt}}Q = Qskew(I^{ - 1} j)$ \\
-+
+  $ \frac{d}{{dt}}\pi  = \sum\limits_i {\left( {Q^T F_i (r,Q)} \right) \times X_i }$ & $\frac{d}{{dt}}\pi  = \pi  \times I^{ - 1} \pi$\\
-+
+  \hline
-+
+\end{tabular}
-+
+\end{center}
-+
+A second-order symplectic method is now obtained by the composition
-+
+of the flow maps,
-+
+\[
-+
+\varphi _{\Delta t}  = \varphi _{\Delta t/2,V}  \circ \varphi
-+
+_{\Delta t,T}  \circ \varphi _{\Delta t/2,V}.
-+
+\]
-+
+Moreover, $\varphi _{\Delta t/2,V}$ can be divided into two
-+
+sub-flows which corresponding to force and torque respectively,
-+
+\[
-+
+\varphi _{\Delta t/2,V}  = \varphi _{\Delta t/2,F}  \circ \varphi
-+
+_{\Delta t/2,\tau }.
-+
+\]
-+
+Since the associated operators of $\varphi _{\Delta t/2,F} $ and
-+
+$\circ \varphi _{\Delta t/2,\tau }$ are commuted, the composition
-+
+order inside $\varphi _{\Delta t/2,V}$ does not matter.
-+
-+
+Furthermore, kinetic potential can be separated to translational
-+
+kinetic term, $T^t (p)$, and rotational kinetic term, $T^r (\pi )$,
-+
+\begin{equation}
-+
+T(p,\pi ) =T^t (p) + T^r (\pi ).
-+
+\end{equation}
-+
+where $ T^t (p) = \frac{1}{2}p^T m^{ - 1} p $ and $T^r (\pi )$ is
-+
+defined by \ref{introEquation:rotationalKineticRB}. Therefore, the
-+
+corresponding flow maps are given by
-+
+\[
-+
+\varphi _{\Delta t,T}  = \varphi _{\Delta t,T^t }  \circ \varphi
-+
+_{\Delta t,T^r }.
-+
+\]
-+
+Finally, we obtain the overall symplectic flow maps for free moving
-+
+rigid body
-+
+\begin{equation}
-+
+\begin{array}{c}
-+
+ \varphi _{\Delta t}  = \varphi _{\Delta t/2,F}  \circ \varphi _{\Delta t/2,\tau }  \\
-+
+  \circ \varphi _{\Delta t,T^t }  \circ \varphi _{\Delta t/2,\pi _1 }  \circ \varphi _{\Delta t/2,\pi _2 }  \circ \varphi _{\Delta t,\pi _3 }  \circ \varphi _{\Delta t/2,\pi _2 }  \circ \varphi _{\Delta t/2,\pi _1 }  \\
-+
+  \circ \varphi _{\Delta t/2,\tau }  \circ \varphi _{\Delta t/2,F}  .\\
-+
+ \end{array}
-+
+\label{introEquation:overallRBFlowMaps}
-+
+\end{equation}
-+
-+
+\section{\label{introSection:langevinDynamics}Langevin Dynamics}
-+
+As an alternative to newtonian dynamics, Langevin dynamics, which
-+
+mimics a simple heat bath with stochastic and dissipative forces,
-+
+has been applied in a variety of studies. This section will review
-+
+the theory of Langevin dynamics simulation. A brief derivation of
-+
+generalized Langevin equation will be given first. Follow that, we
-+
+will discuss the physical meaning of the terms appearing in the
-+
+equation as well as the calculation of friction tensor from
-+
+hydrodynamics theory.
-+
-+
+\subsection{\label{introSection:generalizedLangevinDynamics}Derivation of Generalized Langevin Equation}
-+
-+
+Harmonic bath model, in which an effective set of harmonic
-+
+oscillators are used to mimic the effect of a linearly responding
-+
+environment, has been widely used in quantum chemistry and
-+
+statistical mechanics. One of the successful applications of
-+
+Harmonic bath model is the derivation of Deriving Generalized
-+
+Langevin Dynamics. Lets consider a system, in which the degree of
-+
+freedom $x$ is assumed to couple to the bath linearly, giving a
-+
+Hamiltonian of the form
-+
+\begin{equation}
-+
+H = \frac{{p^2 }}{{2m}} + U(x) + H_B  + \Delta U(x,x_1 , \ldots x_N)
-+
+\label{introEquation:bathGLE}.
-+
+\end{equation}
-+
+Here $p$ is a momentum conjugate to $q$, $m$ is the mass associated
-+
+with this degree of freedom, $H_B$ is harmonic bath Hamiltonian,
-+
+\[
-+
+H_B  = \sum\limits_{\alpha  = 1}^N {\left\{ {\frac{{p_\alpha ^2
-+
+}}{{2m_\alpha  }} + \frac{1}{2}m_\alpha  \omega _\alpha ^2 }
-+
+\right\}}
-+
+\]
-+
+where the index $\alpha$ runs over all the bath degrees of freedom,
-+
+$\omega _\alpha$ are the harmonic bath frequencies, $m_\alpha$ are
-+
+the harmonic bath masses, and $\Delta U$ is bilinear system-bath
-+
+coupling,
-+
+\[
-+
+\Delta U =  - \sum\limits_{\alpha  = 1}^N {g_\alpha  x_\alpha  x}
-+
+\]
-+
+where $g_\alpha$ are the coupling constants between the bath and the
-+
+coordinate $x$. Introducing
-+
+\[
-+
+W(x) = U(x) - \sum\limits_{\alpha  = 1}^N {\frac{{g_\alpha ^2
-+
+}}{{2m_\alpha  w_\alpha ^2 }}} x^2
-+
+\] and combining the last two terms in Equation
-+
+\ref{introEquation:bathGLE}, we may rewrite the Harmonic bath
-+
+Hamiltonian as
-+
+\[
-+
+H = \frac{{p^2 }}{{2m}} + W(x) + \sum\limits_{\alpha  = 1}^N
-+
+{\left\{ {\frac{{p_\alpha ^2 }}{{2m_\alpha  }} + \frac{1}{2}m_\alpha
-+
+w_\alpha ^2 \left( {x_\alpha   - \frac{{g_\alpha  }}{{m_\alpha
-+
+w_\alpha ^2 }}x} \right)^2 } \right\}}
-+
+\]
-+
+Since the first two terms of the new Hamiltonian depend only on the
-+
+system coordinates, we can get the equations of motion for
-+
+Generalized Langevin Dynamics by Hamilton's equations
-+
+\ref{introEquation:motionHamiltonianCoordinate,
-+
+introEquation:motionHamiltonianMomentum},
-+
+\begin{equation}
-+
+m\ddot x =  - \frac{{\partial W(x)}}{{\partial x}} -
-+
+\sum\limits_{\alpha  = 1}^N {g_\alpha  \left( {x_\alpha   -
-+
+\frac{{g_\alpha  }}{{m_\alpha  w_\alpha ^2 }}x} \right)},
-+
+\label{introEquation:coorMotionGLE}
-+
+\end{equation}
-+
+and
-+
+\begin{equation}
-+
+m\ddot x_\alpha   =  - m_\alpha  w_\alpha ^2 \left( {x_\alpha   -
-+
+\frac{{g_\alpha  }}{{m_\alpha  w_\alpha ^2 }}x} \right).
-+
+\label{introEquation:bathMotionGLE}
-+
+\end{equation}
-+
-+
+In order to derive an equation for $x$, the dynamics of the bath
-+
+variables $x_\alpha$ must be solved exactly first. As an integral
-+
+transform which is particularly useful in solving linear ordinary
-+
+differential equations, Laplace transform is the appropriate tool to
-+
+solve this problem. The basic idea is to transform the difficult
-+
+differential equations into simple algebra problems which can be
-+
+solved easily. Then applying inverse Laplace transform, also known
-+
+as the Bromwich integral, we can retrieve the solutions of the
-+
+original problems.
-+
-+
+Let $f(t)$ be a function defined on $ [0,\infty ) $. The Laplace
-+
+transform of f(t) is a new function defined as
-+
+\[
-+
+L(f(t)) \equiv F(p) = \int_0^\infty  {f(t)e^{ - pt} dt}
-+
+\]
-+
+where  $p$ is real and  $L$ is called the Laplace Transform
-+
+Operator. Below are some important properties of Laplace transform
-+
+\begin{equation}
-+
+\begin{array}{c}
-+
+ L(x + y) = L(x) + L(y) \\
-+
+ L(ax) = aL(x) \\
-+
+ L(\dot x) = pL(x) - px(0) \\
-+
+ L(\ddot x) = p^2 L(x) - px(0) - \dot x(0) \\
-+
+ L\left( {\int_0^t {g(t - \tau )h(\tau )d\tau } } \right) = G(p)H(p) \\
-+
+ \end{array}
-+
+\end{equation}
-+
-+
+Applying Laplace transform to the bath coordinates, we obtain
-+
+\[
-+
+\begin{array}{c}
-+
+ p^2 L(x_\alpha  ) - px_\alpha  (0) - \dot x_\alpha  (0) =  - \omega _\alpha ^2 L(x_\alpha  ) + \frac{{g_\alpha  }}{{\omega _\alpha  }}L(x) \\
-+
+ L(x_\alpha  ) = \frac{{\frac{{g_\alpha  }}{{\omega _\alpha  }}L(x) + px_\alpha  (0) + \dot x_\alpha  (0)}}{{p^2  + \omega _\alpha ^2 }} \\
-+
+ \end{array}
-+
+\]
-+
+By the same way, the system coordinates become
-+
+\[
-+
+\begin{array}{c}
-+
+ mL(\ddot x) =  - \frac{1}{p}\frac{{\partial W(x)}}{{\partial x}} \\
-+
+  - \sum\limits_{\alpha  = 1}^N {\left\{ { - \frac{{g_\alpha ^2 }}{{m_\alpha  \omega _\alpha ^2 }}\frac{p}{{p^2  + \omega _\alpha ^2 }}pL(x) - \frac{p}{{p^2  + \omega _\alpha ^2 }}g_\alpha  x_\alpha  (0) - \frac{1}{{p^2  + \omega _\alpha ^2 }}g_\alpha  \dot x_\alpha  (0)} \right\}}  \\
-+
+ \end{array}
-+
+\]
-+
-+
+With the help of some relatively important inverse Laplace
-+
+transformations:
-+
+\[
-+
+\begin{array}{c}
-+
+ L(\cos at) = \frac{p}{{p^2  + a^2 }} \\
-+
+ L(\sin at) = \frac{a}{{p^2  + a^2 }} \\
-+
+ L(1) = \frac{1}{p} \\
-+
+ \end{array}
-+
+\]
-+
+, we obtain
+\begin{align}
+m\ddot x &=  - \frac{{\partial W(x)}}{{\partial x}} -
+\sum\limits_{\alpha  = 1}^N {\left\{ {\left( { - \frac{{g_\alpha ^2
+(\omega _\alpha  t)} \right\}}
+\end{align}
-+
+Introducing a \emph{dynamic friction kernel}
+\begin{equation}
-+
+\xi (t) = \sum\limits_{\alpha  = 1}^N {\left( { - \frac{{g_\alpha ^2
-+
+}}{{m_\alpha  \omega _\alpha ^2 }}} \right)\cos (\omega _\alpha  t)}
-+
+\label{introEquation:dynamicFrictionKernelDefinition}
-+
+\end{equation}
-+
+and \emph{a random force}
-+
+\begin{equation}
-+
+R(t) = \sum\limits_{\alpha  = 1}^N {\left( {g_\alpha  x_\alpha  (0)
-+
+- \frac{{g_\alpha ^2 }}{{m_\alpha  \omega _\alpha ^2 }}x(0)}
-+
+\right)\cos (\omega _\alpha  t)}  + \frac{{\dot x_\alpha
-+
+(0)}}{{\omega _\alpha  }}\sin (\omega _\alpha  t),
-+
+\label{introEquation:randomForceDefinition}
-+
+\end{equation}
-+
+the equation of motion can be rewritten as
-+
+\begin{equation}
+m\ddot x =  - \frac{{\partial W}}{{\partial x}} - \int_0^t {\xi
+(t)\dot x(t - \tau )d\tau }  + R(t)
+\label{introEuqation:GeneralizedLangevinDynamics}
+\end{equation}
-<
+%where $ {\xi (t)}$ is friction kernel, $R(t)$ is random force and
-<
+%$W$ is the potential of mean force. $W(x) =  - kT\ln p(x)$
->
+which is known as the \emph{generalized Langevin equation}.
->
->
+\subsubsection{\label{introSection:randomForceDynamicFrictionKernel}Random Force and Dynamic Friction Kernel}
->
->
+One may notice that $R(t)$ depends only on initial conditions, which
->
+implies it is completely deterministic within the context of a
->
+harmonic bath. However, it is easy to verify that $R(t)$ is totally
->
+uncorrelated to $x$ and $\dot x$,
+\[
-<
+\xi (t) = \sum\limits_{\alpha  = 1}^N {\left( { - \frac{{g_\alpha ^2
-<
+}}{{m_\alpha  \omega _\alpha ^2 }}} \right)\cos (\omega _\alpha  t)}
->
+\begin{array}{l}
->
+ \left\langle {x(t)R(t)} \right\rangle  = 0, \\
->
+ \left\langle {\dot x(t)R(t)} \right\rangle  = 0. \\
->
+ \end{array}
+\]
-<
+For an infinite harmonic bath, we can use the spectral density and
-<
+an integral over frequencies.
->
+This property is what we expect from a truly random process. As long
->
+as the model, which is gaussian distribution in general, chosen for
->
+$R(t)$ is a truly random process, the stochastic nature of the GLE
->
+still remains.
-+
+%dynamic friction kernel
-+
+The convolution integral
+\[
-<
+R(t) = \sum\limits_{\alpha  = 1}^N {\left( {g_\alpha  x_\alpha  (0)
-<
+- \frac{{g_\alpha ^2 }}{{m_\alpha  \omega _\alpha ^2 }}x(0)}
-<
+\right)\cos (\omega _\alpha  t)}  + \frac{{\dot x_\alpha
-<
+(0)}}{{\omega _\alpha  }}\sin (\omega _\alpha  t)
->
+\int_0^t {\xi (t)\dot x(t - \tau )d\tau }
+\]
-<
+The random forces depend only on initial conditions.
->
+depends on the entire history of the evolution of $x$, which implies
->
+that the bath retains memory of previous motions. In other words,
->
+the bath requires a finite time to respond to change in the motion
->
+of the system. For a sluggish bath which responds slowly to changes
->
+in the system coordinate, we may regard $\xi(t)$ as a constant
->
+$\xi(t) = \Xi_0$. Hence, the convolution integral becomes
->
+\[
->
+\int_0^t {\xi (t)\dot x(t - \tau )d\tau }  = \xi _0 (x(t) - x(0))
->
+\]
->
+and Equation \ref{introEuqation:GeneralizedLangevinDynamics} becomes
->
+\[
->
+m\ddot x =  - \frac{\partial }{{\partial x}}\left( {W(x) +
->
+\frac{1}{2}\xi _0 (x - x_0 )^2 } \right) + R(t),
->
+\]
->
+which can be used to describe dynamic caging effect. The other
->
+extreme is the bath that responds infinitely quickly to motions in
->
+the system. Thus, $\xi (t)$ can be taken as a $delta$ function in
->
+time:
->
+\[
->
+\xi (t) = 2\xi _0 \delta (t)
->
+\]
->
+Hence, the convolution integral becomes
->
+\[
->
+\int_0^t {\xi (t)\dot x(t - \tau )d\tau }  = 2\xi _0 \int_0^t
->
+{\delta (t)\dot x(t - \tau )d\tau }  = \xi _0 \dot x(t),
->
+\]
->
+and Equation \ref{introEuqation:GeneralizedLangevinDynamics} becomes
->
+\begin{equation}
->
+m\ddot x =  - \frac{{\partial W(x)}}{{\partial x}} - \xi _0 \dot
->
+x(t) + R(t) \label{introEquation:LangevinEquation}
->
+\end{equation}
->
+which is known as the Langevin equation. The static friction
->
+coefficient $\xi _0$ can either be calculated from spectral density
->
+or be determined by Stokes' law for regular shaped particles.A
->
+briefly review on calculating friction tensor for arbitrary shaped
->
+particles is given in Sec.~\ref{introSection:frictionTensor}.
+\subsubsection{\label{introSection:secondFluctuationDissipation}The Second Fluctuation Dissipation Theorem}
-<
+So we can define a new set of coordinates,
->
->
+Defining a new set of coordinates,
+\[
+q_\alpha  (t) = x_\alpha  (t) - \frac{1}{{m_\alpha  \omega _\alpha
+^2 }}x(0)
-<
+\]
-<
+This makes
->
+\],
->
+we can rewrite $R(T)$ as
+\[
-<
+R(t) = \sum\limits_{\alpha  = 1}^N {g_\alpha  q_\alpha  (t)}
->
+R(t) = \sum\limits_{\alpha  = 1}^N {g_\alpha  q_\alpha  (t)}.
+\]
+And since the $q$ coordinates are harmonic oscillators,
+\[
-<
+\begin{array}{l}
->
+\begin{array}{c}
->
+ \left\langle {q_\alpha ^2 } \right\rangle  = \frac{{kT}}{{m_\alpha  \omega _\alpha ^2 }} \\
+ \left\langle {q_\alpha  (t)q_\alpha  (0)} \right\rangle  = \left\langle {q_\alpha ^2 (0)} \right\rangle \cos (\omega _\alpha  t) \\
+ \left\langle {q_\alpha  (t)q_\beta  (0)} \right\rangle  = \delta _{\alpha \beta } \left\langle {q_\alpha  (t)q_\alpha  (0)} \right\rangle  \\
-+
+ \left\langle {R(t)R(0)} \right\rangle  = \sum\limits_\alpha  {\sum\limits_\beta  {g_\alpha  g_\beta  \left\langle {q_\alpha  (t)q_\beta  (0)} \right\rangle } }  \\
-+
+  = \sum\limits_\alpha  {g_\alpha ^2 \left\langle {q_\alpha ^2 (0)} \right\rangle \cos (\omega _\alpha  t)}  \\
-+
+  = kT\xi (t) \\
+ \end{array}
+\]
-+
+Thus, we recover the \emph{second fluctuation dissipation theorem}
-+
+\begin{equation}
-+
+\xi (t) = \left\langle {R(t)R(0)} \right\rangle
-+
+\label{introEquation:secondFluctuationDissipation}.
-+
+\end{equation}
-+
+In effect, it acts as a constraint on the possible ways in which one
-+
+can model the random force and friction kernel.
-<
+\begin{align}
-<
+\left\langle {R(t)R(0)} \right\rangle  &= \sum\limits_\alpha
-<
+{\sum\limits_\beta  {g_\alpha  g_\beta  \left\langle {q_\alpha
-<
+(t)q_\beta  (0)} \right\rangle } }
-<
+%
-<
+&= \sum\limits_\alpha  {g_\alpha ^2 \left\langle {q_\alpha ^2 (0)}
-<
+\right\rangle \cos (\omega _\alpha  t)}
-<
+%
-<
+&= kT\xi (t)
-<
+\end{align}
->
+\subsection{\label{introSection:frictionTensor} Friction Tensor}
->
+Theoretically, the friction kernel can be determined using velocity
->
+autocorrelation function. However, this approach become impractical
->
+when the system become more and more complicate. Instead, various
->
+approaches based on hydrodynamics have been developed to calculate
->
+the friction coefficients. The friction effect is isotropic in
->
+Equation, \zeta can be taken as a scalar. In general, friction
->
+tensor \Xi is a $6\times 6$ matrix given by
->
+\[
->
+\Xi  = \left( {\begin{array}{*{20}c}
->
+   {\Xi _{}^{tt} } & {\Xi _{}^{rt} }  \\
->
+   {\Xi _{}^{tr} } & {\Xi _{}^{rr} }  \\
->
+\end{array}} \right).
->
+\]
->
+Here, $ {\Xi^{tt} }$ and $ {\Xi^{rr} }$ are translational friction
->
+tensor and rotational resistance (friction) tensor respectively,
->
+while ${\Xi^{tr} }$ is translation-rotation coupling tensor and $
->
+{\Xi^{rt} }$ is rotation-translation coupling tensor. When a
->
+particle moves in a fluid, it may experience friction force or
->
+torque along the opposite direction of the velocity or angular
->
+velocity,
->
+\[
->
+\left( \begin{array}{l}
->
+ F_R  \\
->
+ \tau _R  \\
->
+ \end{array} \right) =  - \left( {\begin{array}{*{20}c}
->
+   {\Xi ^{tt} } & {\Xi ^{rt} }  \\
->
+   {\Xi ^{tr} } & {\Xi ^{rr} }  \\
->
+\end{array}} \right)\left( \begin{array}{l}
->
+ v \\
->
+ w \\
->
+ \end{array} \right)
->
+\]
->
+where $F_r$ is the friction force and $\tau _R$ is the friction
->
+toque.
-+
+\subsubsection{\label{introSection:resistanceTensorRegular}The Resistance Tensor for Regular Shape}
-+
-+
+For a spherical particle, the translational and rotational friction
-+
+constant can be calculated from Stoke's law,
-+
+\[
-+
+\Xi ^{tt}  = \left( {\begin{array}{*{20}c}
-+
+   {6\pi \eta R} & 0 & 0  \\
-+
+& {6\pi \eta R} & 0  \\
-+
+& 0 & {6\pi \eta R}  \\
-+
+\end{array}} \right)
-+
+\]
-+
+and
-+
+\[
-+
+\Xi ^{rr}  = \left( {\begin{array}{*{20}c}
-+
+   {8\pi \eta R^3 } & 0 & 0  \\
-+
+& {8\pi \eta R^3 } & 0  \\
-+
+& 0 & {8\pi \eta R^3 }  \\
-+
+\end{array}} \right)
-+
+\]
-+
+where $\eta$ is the viscosity of the solvent and $R$ is the
-+
+hydrodynamics radius.
-+
-+
+Other non-spherical shape, such as cylinder and ellipsoid
-+
+\textit{etc}, are widely used as reference for developing new
-+
+hydrodynamics theory, because their properties can be calculated
-+
+exactly. In 1936, Perrin extended Stokes's law to general ellipsoid,
-+
+also called a triaxial ellipsoid, which is given in Cartesian
-+
+coordinates by
-+
+\[
-+
+\frac{{x^2 }}{{a^2 }} + \frac{{y^2 }}{{b^2 }} + \frac{{z^2 }}{{c^2
-+
+}} = 1
-+
+\]
-+
+where the semi-axes are of lengths $a$, $b$, and $c$. Unfortunately,
-+
+due to the complexity of the elliptic integral, only the ellipsoid
-+
+with the restriction of two axes having to be equal, \textit{i.e.}
-+
+prolate($ a \ge b = c$) and oblate ($ a < b = c $), can be solved
-+
+exactly. Introducing an elliptic integral parameter $S$ for prolate,
-+
+\[
-+
+S = \frac{2}{{\sqrt {a^2  - b^2 } }}\ln \frac{{a + \sqrt {a^2  - b^2
-+
+} }}{b},
-+
+\]
-+
+and oblate,
-+
+\[
-+
+S = \frac{2}{{\sqrt {b^2  - a^2 } }}arctg\frac{{\sqrt {b^2  - a^2 }
-+
+}}{a}
-+
+\],
-+
+one can write down the translational and rotational resistance
-+
+tensors
-+
+\[
-+
+\begin{array}{l}
-+
+ \Xi _a^{tt}  = 16\pi \eta \frac{{a^2  - b^2 }}{{(2a^2  - b^2 )S - 2a}} \\
-+
+ \Xi _b^{tt}  = \Xi _c^{tt}  = 32\pi \eta \frac{{a^2  - b^2 }}{{(2a^2  - 3b^2 )S + 2a}} \\
-+
+ \end{array},
-+
+\]
-+
+and
-+
+\[
-+
+\begin{array}{l}
-+
+ \Xi _a^{rr}  = \frac{{32\pi }}{3}\eta \frac{{(a^2  - b^2 )b^2 }}{{2a - b^2 S}} \\
-+
+ \Xi _b^{rr}  = \Xi _c^{rr}  = \frac{{32\pi }}{3}\eta \frac{{(a^4  - b^4 )}}{{(2a^2  - b^2 )S - 2a}} \\
-+
+ \end{array}.
-+
+\]
-+
-+
+\subsubsection{\label{introSection:resistanceTensorRegularArbitrary}The Resistance Tensor for Arbitrary Shape}
-+
-+
+Unlike spherical and other regular shaped molecules, there is not
-+
+analytical solution for friction tensor of any arbitrary shaped
-+
+rigid molecules. The ellipsoid of revolution model and general
-+
+triaxial ellipsoid model have been used to approximate the
-+
+hydrodynamic properties of rigid bodies. However, since the mapping
-+
+from all possible ellipsoidal space, $r$-space, to all possible
-+
+combination of rotational diffusion coefficients, $D$-space is not
-+
+unique\cite{Wegener79} as well as the intrinsic coupling between
-+
+translational and rotational motion of rigid body\cite{}, general
-+
+ellipsoid is not always suitable for modeling arbitrarily shaped
-+
+rigid molecule. A number of studies have been devoted to determine
-+
+the friction tensor for irregularly shaped rigid bodies using more
-+
+advanced method\cite{} where the molecule of interest was modeled by
-+
+combinations of spheres(beads)\cite{} and the hydrodynamics
-+
+properties of the molecule can be calculated using the hydrodynamic
-+
+interaction tensor. Let us consider a rigid assembly of $N$ beads
-+
+immersed in a continuous medium. Due to hydrodynamics interaction,
-+
+the ``net'' velocity of $i$th bead, $v'_i$ is different than its
-+
+unperturbed velocity $v_i$,
-+
+\[
-+
+v'_i  = v_i  - \sum\limits_{j \ne i} {T_{ij} F_j }
-+
+\]
-+
+where $F_i$ is the frictional force, and $T_{ij}$ is the
-+
+hydrodynamic interaction tensor. The friction force of $i$th bead is
-+
+proportional to its ``net'' velocity
+\begin{equation}
-<
+\xi (t) = \left\langle {R(t)R(0)} \right\rangle
-<
+\label{introEquation:secondFluctuationDissipation}
->
+F_i  = \zeta _i v_i  - \zeta _i \sum\limits_{j \ne i} {T_{ij} F_j }.
->
+\label{introEquation:tensorExpression}
+\end{equation}
-+
+This equation is the basis for deriving the hydrodynamic tensor. In
-+
+, Oseen and Burgers gave a simple solution to Equation
-+
+\ref{introEquation:tensorExpression}
-+
+\begin{equation}
-+
+T_{ij}  = \frac{1}{{8\pi \eta r_{ij} }}\left( {I + \frac{{R_{ij}
-+
+R_{ij}^T }}{{R_{ij}^2 }}} \right).
-+
+\label{introEquation:oseenTensor}
-+
+\end{equation}
-+
+Here $R_{ij}$ is the distance vector between bead $i$ and bead $j$.
-+
+A second order expression for element of different size was
-+
+introduced by Rotne and Prager\cite{} and improved by Garc\'{i}a de
-+
+la Torre and Bloomfield,
-+
+\begin{equation}
-+
+T_{ij}  = \frac{1}{{8\pi \eta R_{ij} }}\left[ {\left( {I +
-+
+\frac{{R_{ij} R_{ij}^T }}{{R_{ij}^2 }}} \right) + R\frac{{\sigma
-+
+_i^2  + \sigma _j^2 }}{{r_{ij}^2 }}\left( {\frac{I}{3} -
-+
+\frac{{R_{ij} R_{ij}^T }}{{R_{ij}^2 }}} \right)} \right].
-+
+\label{introEquation:RPTensorNonOverlapped}
-+
+\end{equation}
-+
+Both of the Equation \ref{introEquation:oseenTensor} and Equation
-+
+\ref{introEquation:RPTensorNonOverlapped} have an assumption $R_{ij}
-+
+\ge \sigma _i  + \sigma _j$. An alternative expression for
-+
+overlapping beads with the same radius, $\sigma$, is given by
-+
+\begin{equation}
-+
+T_{ij}  = \frac{1}{{6\pi \eta R_{ij} }}\left[ {\left( {1 -
-+
+\frac{2}{{32}}\frac{{R_{ij} }}{\sigma }} \right)I +
-+
+\frac{2}{{32}}\frac{{R_{ij} R_{ij}^T }}{{R_{ij} \sigma }}} \right]
-+
+\label{introEquation:RPTensorOverlapped}
-+
+\end{equation}
-<
+\section{\label{introSection:hydroynamics}Hydrodynamics}
->
+To calculate the resistance tensor at an arbitrary origin $O$, we
->
+construct a $3N \times 3N$ matrix consisting of $N \times N$
->
+$B_{ij}$ blocks
->
+\begin{equation}
->
+B = \left( {\begin{array}{*{20}c}
->
+   {B_{11} } &  \ldots  & {B_{1N} }  \\
->
+    \vdots  &  \ddots  &  \vdots   \\
->
+   {B_{N1} } &  \cdots  & {B_{NN} }  \\
->
+\end{array}} \right),
->
+\end{equation}
->
+where $B_{ij}$ is given by
->
+\[
->
+B_{ij}  = \delta _{ij} \frac{I}{{6\pi \eta R}} + (1 - \delta _{ij}
->
+)T_{ij}
->
+\]
->
+where $\delta _{ij}$ is Kronecker delta function. Inverting matrix
->
+$B$, we obtain
-<
+\subsection{\label{introSection:frictionTensor} Friction Tensor}
-<
+\subsection{\label{introSection:analyticalApproach}Analytical
-<
+Approach}
->
+\[
->
+C = B^{ - 1}  = \left( {\begin{array}{*{20}c}
->
+   {C_{11} } &  \ldots  & {C_{1N} }  \\
->
+    \vdots  &  \ddots  &  \vdots   \\
->
+   {C_{N1} } &  \cdots  & {C_{NN} }  \\
->
+\end{array}} \right)
->
+\]
->
+, which can be partitioned into $N \times N$ $3 \times 3$ block
->
+$C_{ij}$. With the help of $C_{ij}$ and skew matrix $U_i$
->
+\[
->
+U_i  = \left( {\begin{array}{*{20}c}
->
+& { - z_i } & {y_i }  \\
->
+   {z_i } & 0 & { - x_i }  \\
->
+   { - y_i } & {x_i } & 0  \\
->
+\end{array}} \right)
->
+\]
->
+where $x_i$, $y_i$, $z_i$ are the components of the vector joining
->
+bead $i$ and origin $O$. Hence, the elements of resistance tensor at
->
+arbitrary origin $O$ can be written as
->
+\begin{equation}
->
+\begin{array}{l}
->
+ \Xi _{}^{tt}  = \sum\limits_i {\sum\limits_j {C_{ij} } } , \\
->
+ \Xi _{}^{tr}  = \Xi _{}^{rt}  = \sum\limits_i {\sum\limits_j {U_i C_{ij} } } , \\
->
+ \Xi _{}^{rr}  =  - \sum\limits_i {\sum\limits_j {U_i C_{ij} } } U_j  \\
->
+ \end{array}
->
+\label{introEquation:ResistanceTensorArbitraryOrigin}
->
+\end{equation}
-<
+\subsection{\label{introSection:approximationApproach}Approximation
-<
+Approach}
->
+The resistance tensor depends on the origin to which they refer. The
->
+proper location for applying friction force is the center of
->
+resistance (reaction), at which the trace of rotational resistance
->
+tensor, $ \Xi ^{rr}$ reaches minimum. Mathematically, the center of
->
+resistance is defined as an unique point of the rigid body at which
->
+the translation-rotation coupling tensor are symmetric,
->
+\begin{equation}
->
+\Xi^{tr}  = \left( {\Xi^{tr} } \right)^T
->
+\label{introEquation:definitionCR}
->
+\end{equation}
->
+Form Equation \ref{introEquation:ResistanceTensorArbitraryOrigin},
->
+we can easily find out that the translational resistance tensor is
->
+origin independent, while the rotational resistance tensor and
->
+translation-rotation coupling resistance tensor depend on the
->
+origin. Given resistance tensor at an arbitrary origin $O$, and a
->
+vector ,$r_{OP}(x_{OP}, y_{OP}, z_{OP})$, from $O$ to $P$, we can
->
+obtain the resistance tensor at $P$ by
->
+\begin{equation}
->
+\begin{array}{l}
->
+ \Xi _P^{tt}  = \Xi _O^{tt}  \\
->
+ \Xi _P^{tr}  = \Xi _P^{rt}  = \Xi _O^{tr}  - U_{OP} \Xi _O^{tt}  \\
->
+ \Xi _P^{rr}  = \Xi _O^{rr}  - U_{OP} \Xi _O^{tt} U_{OP}  + \Xi _O^{tr} U_{OP}  - U_{OP} \Xi _O^{tr} ^{^T }  \\
->
+ \end{array}
->
+ \label{introEquation:resistanceTensorTransformation}
->
+\end{equation}
->
+where
->
+\[
->
+U_{OP}  = \left( {\begin{array}{*{20}c}
->
+& { - z_{OP} } & {y_{OP} }  \\
->
+   {z_i } & 0 & { - x_{OP} }  \\
->
+   { - y_{OP} } & {x_{OP} } & 0  \\
->
+\end{array}} \right)
->
+\]
->
+Using Equations \ref{introEquation:definitionCR} and
->
+\ref{introEquation:resistanceTensorTransformation}, one can locate
->
+the position of center of resistance,
->
+\[
->
+\left( \begin{array}{l}
->
+ x_{OR}  \\
->
+ y_{OR}  \\
->
+ z_{OR}  \\
->
+ \end{array} \right) = \left( {\begin{array}{*{20}c}
->
+   {(\Xi _O^{rr} )_{yy}  + (\Xi _O^{rr} )_{zz} } & { - (\Xi _O^{rr} )_{xy} } & { - (\Xi _O^{rr} )_{xz} }  \\
->
+   { - (\Xi _O^{rr} )_{xy} } & {(\Xi _O^{rr} )_{zz}  + (\Xi _O^{rr} )_{xx} } & { - (\Xi _O^{rr} )_{yz} }  \\
->
+   { - (\Xi _O^{rr} )_{xz} } & { - (\Xi _O^{rr} )_{yz} } & {(\Xi _O^{rr} )_{xx}  + (\Xi _O^{rr} )_{yy} }  \\
->
+\end{array}} \right)^{ - 1} \left( \begin{array}{l}
->
+ (\Xi _O^{tr} )_{yz}  - (\Xi _O^{tr} )_{zy}  \\
->
+ (\Xi _O^{tr} )_{zx}  - (\Xi _O^{tr} )_{xz}  \\
->
+ (\Xi _O^{tr} )_{xy}  - (\Xi _O^{tr} )_{yx}  \\
->
+ \end{array} \right).
->
+\]
->
+where $x_OR$, $y_OR$, $z_OR$ are the components of the vector
->
+joining center of resistance $R$ and origin $O$.
-<
+\subsection{\label{introSection:centersRigidBody}Centers of Rigid
-<
+Body}
->
+%\section{\label{introSection:correlationFunctions}Correlation Functions}

Diff Legend

-–
+Removed lines
-+
+Added lines
-<
+Changed lines
->
+Changed lines

Comparing trunk/tengDissertation/Introduction.tex (file contents): Revision 2697 by tim, Fri Apr 7 05:03:54 2006 UTC vs. Revision 2720 by tim, Wed Apr 19 19:46:53 2006 UTC

Diff Legend

Comparing trunk/tengDissertation/Introduction.tex (file contents):
Revision 2697 by tim, Fri Apr 7 05:03:54 2006 UTC vs.
Revision 2720 by tim, Wed Apr 19 19:46:53 2006 UTC